Showing posts with label demonstration. Show all posts
Showing posts with label demonstration. Show all posts

Sunday, November 13, 2011

The standing lamp for our "new" living room is finished. We took all the pieces and, this afternoon, put them together. I made sure to document the process (beginning with an earlier post chronicling the part where I made the different pottery components). So, here it goes.

First, our list of supplies:
A standing lamp (which we disassembled by removing the electric cord)
Pottery pieces (enough to go to the height of the decorative piece below the actual fixture), including a "cap" piece).
2" PVC pipe
Foam spray (to "set" the PVC pipe against the metal pole of the lamp).
Silicone (to attach and anchor the separate pottery pieces to each other).
A replacement plug (since we had to remove the old one to remove the wire so we could put the whole thing together -- a long story).

We took the PVC pipe and loaded the pottery pieces onto it. I'd already checked the height of the pieces against the lamp and, being really, REALLY lucky, they were the perfect height.


At this stage, everything was just sitting one on the other, so we could make adjustments and figure things out. We decided to switch the order of the pottery a little, switching around the bottom piece with the blue piece (fourth from the bottom).

Then we marked the PVC pipe where it needed to be cut and took everything apart again.

Then Avie, my favorite husband and incredible handyman, took the PVC pipe outside to cut. He cut it 1/4" below our marked line.

Then we brought it back in and put it on the lamp. At the top, we sprayed in some insulating foam sealant so the PVC pipe would be fixed in place. We only needed to do this at the top, since the bottom sat squarely around a "hump" from the lamp base, holding that part quite nicely. Then we allowed the foam to set for a few minutes.



The wire you see sticking up through the center is the guide wire we were going to use to pull the original electric cord back down through the lamp. We had to do this because you can't drop pottery pieces down with everything attached. We didn't think about this until we started looking at everything after we purchased this lamp at the Salvation Army.

When the foam had set up a little, we began loading on the pottery, putting a line of silicone where they joined the PVC and each other, to keep them secure and to prevent them from shifting.


Finally, we had all the pieces loaded.



When the insulating foam dries, it also expands. Avie trimmed the foam so it wouldn't block the threads where we would be screwing the lamp back together.

Then it was time to pull the electrical cord back through. He threaded the guide wire through the cord and gently used it to guide everything back through the bottom two holes of the lamp. It worked like a charm except, in the excitement, we'd forgotten to put the pottery finishing cap on. So, the first time was for practice. We put everything back the way it was, put on the cap, and rewired the lamp a second time.




Then it was just a matter of attaching the cap piece, attaching the new plug, screwing in the top, and making sure everything worked.

It did!
 
All in all, it was a fabulous experience resulting in a tremendous sense of pride AND a fabulous piece for the formal living room.

Let me know what YOU think!

Friday, July 01, 2011

Last night I did a workshop in our studio on layered underglaze/colored slip surface decoration. It's a technique I learned when I attended The Surface Decoration workshop through the Potter's Guild in Temple, TX a couple of months ago.

I've been playing with the technique all week and have become incredibly inspired by the process. I'll walk you through the workshop so you might become inspired as well.

Here's the initial setup for the workshop. From the left side: slab prepared for platter demo, tile prepped for technique demo, sample stencils/sample patterns/heat wire, plaster molds, samples of finished pieces using technique. Please ignore the soft drink in the photo. It's not mine.






This is the stencil I used for the platter. It's adapted from a Judaica papercut. Papercuts are, for all intents and purposes, stencils. After sizing it correctly, using Picasa software, I traced it onto my .010 Lexan and cut it using a stencil heat wire. I'd say the stencil took me about two hours total, from printing to finished piece.

First I did a demo on a tile I had prepped earlier. (Everyone had two tiles to play with -- everyone only had time enough to complete one.) The prep involved painting black underglaze on the surface of the tile and allowing it to dry to matte consistency, while keeping the tile itself moist and pliable.
 I began by carving a series of angled lines as a backdrop. The lines will fire the color of the clay which, in this case, is low fire white.


You could just as easily make swirls, geometric patterns, or not carve at all. But the technique is about layers, so I carved.

 Being a little bit OCD in the studio, I used a ruler for my lines.

Then I took a stencil (a commercial one in this case) and used a rolling pin to embed it into the clay. 

The idea is you want the clay to come up so its surface is level with the top of the stencil. This will prevent your underglaze or slip from bleeding, giving you a crisp, clear image.







Because I used a black foundation color, which muddies overlying colors, I put a base coat of white underglaze. This acts the same way a primer does, helping your lighter colors pop. If you're going from light base to dark, this step is probably not necessary.


Then we had to "hurry up and wait" for this base layer to dry to matte. When the tiles are done, and dry enough, they'll be placed on a plaster slab and rolled over, to flatten the design side. It's important to compress the layers, leaving a smooth surface. This decreases your chances of cracking along stress lines created by carving and raising clay through the stencil/s.


At this point I had everyone base coat their tiles with the color of their choice.

While all the tiles dried I moved onto the platter demo .


Remember the stencil in an earlier photo? I used it for this platter. Since the stencil would block the pattern, I used Fossil Gray Amaco Velvet underglaze, which would give me a stonelike effect. It's fires gray with tiny black spots. 


When that dried to matte, I rolled on my stencil and used Medium Blue over it. This was the result when I peeled off the stencil.









I placed my "Shabbat" (in Hebrew, since I do Judaica) stencil over the centerpiece of the slab, trying to center it correctly.


Then, just as on the tile, I used a roller to fix it into place, again making sure the clay came up level with the top of the stencil.







Using black underglaze, I painted on a couple of coats and waited for it to set.


It doesn't need to dry completely before removing the stencil. It just needs to set enough so it won't smear.









Here it is, with the stencil removed.













Throughout the process, it's important to make sure your slab remains pliable. I do this by spraying plastic and laying the slab over that. Then, periodically, I pick up the slab and spray some more. Since the slab is about 1/2" thick, this keeps the clay pliable, while still allowing the surface colors to dry.








Once my underglazes have dried so they're no longer tacky to the touch, I cut out my platter.












                                                                             


Now let's backtrack a couple of steps. While I was waiting for my underglazes to dry, I took a plaster hump mold and centered it on a foam bat. I'll be using this to shape my platter.

Here I've begun shaping the slab against the mold using a rubber rib. You could just as easily use a wooden one. The idea is initially to use lighter pressure, molding the clay to the shape of the mold.

I slowly increased pressure on the clay, both compressing the piece and trying to flatten out the textured layers from the carvings and the raised stencil parts. This is to prevent cracking from multiple sources: not enough compression of the slab (especially on a larger piece), stress from the carvings and raised lines from the stencil. This also gives a nice, smooth surface to the inside of the functional piece.

Compress, compress, compress.........

When I feel I've finished compressing, I take a serrated rib and score the bottom where I want to place my foot. I do this while the wheel is moving, making it simple to be sure the foot will be centered. The step missing here is that I trimmed the rim of the platter with the pointed tip of a sculpting stick. Then I used a damp sponge to smooth off the sharp edge. Then I just trimmed up a little along the inside. I smooth that off when the platter is removed from the mold.


     


Then I put slip over the scoring. I'm using slip made from my clay body with water and a little vinegar to act as a flocculant.

I've made a coil using a handle cutter. You could just as easily roll one or use an extruder. I've scored the coil, slipped it, and joined it to the bottom of my platter.

I laid the ends of the coil one over the other and make an angular cut through both, to create a joining edge. I set the wheel to spin and work with the foot, centering it and bringing clay down to join it seamlessly to the body of the platter. I work on this a bit, making sure the foot is compressed, centered, and well joined.

Here's a photo of the finished platter (note the cleaned up edge), and a bit of the tile with Amethyst having been painted over the white base.







 The technique has all sorts of possibilities. I encouraged my students to play with it, telling them I'd love to see where they take it and how they make it their own.

Sunday, February 21, 2010

I've been promising a demo and I needed to remake the baby gift that blew up in the kiln, so I took the opportunity to combine the two. So, these are the deep dark secrets of my upcoming custom baby plate series using the wonderful art of my good friend David Kaminsky.

I begin with a plate that has dried to almost leather, meaning it's no longer tacky to the touch, but still has a decent amount of give in its softness.

I print out a scanned copy of the art I'm using, sizing it to the area I need to cover. Then, because making an impression of this size using the paper leaves remnants of said paper on the damp clay, I trace the pattern onto a piece of plastic wrap using a permanent marker. I then use this to gently incise the pattern onto my plate.



Once the pattern is completely incised, I grab my Amaco Velvet Underglazes and consider my color options.

 

Then I just start painting. I use a few different brushes, all natural fiber. 

I don't worry too much about the details. These can be cleaned up later when the underglazes have dried, but the clay is still moist. For the most intense color I use three coats of each color. Because I'm anal, I only work with one color at a time, allowing each coat to dry in between. The clay tends to absorb a lot of the moisture, so three coats usually doesn't take very long.

For the sky background, because I don't want the plate to be overpowering, I use a "wash" coat of the underglaze rather than the intensity three coats would offer. This is done with a quick single coat.

Then it's time to add the name. I know -- I could have just done it on the same plastic I used for the main picture. But the letters are more delicate and I prefer using the heavier quality of paper for this and, since the paper doesn't sit on the clay for long when incising the name, I don't get any paper fibers stuck to the clay.



Finally, I fill in the letters for the name, use my incising tool to accent the definition lines, clean up any small smudges, and the initial work on the baby plate is done. It will go in for a bisque firing, which will bring out the stronger shades of the underglaze though, unlike regular glaze, they won't change too much from what you see here.



To be continued.........